SAVE THESE INSTRUCTIONS
6
GENERAL INSTRUCTIONSGENERAL INSTRUCTIONS
1) Move the furniture around to give a clear working
area. Cover bottoms of furniture legs where possible.
(aluminum foil or foam blocks are ideal)
Pin up curtains and drapes.
2) Have a suitable size clean bucket available for filling
the solution tank with warm water. CAUTION: - Do
not add the cleaning agent at this stage
3) Adjust the machine brush operating depth with the
knob on the back of models PFX 7S & 9S (FIG. 1A)
and the front of PFX4S (FIG. 1B) to suit the carpet
height. NOTE: The raised counter clockwise position
of the knob should be used when the machine is being
stored. NOTE: Excess brush contact may overload
motor circuit breaker or reduce wet extraction quality.
4) Remove the transparent cover and remove the recov-
ery tank below cover. .(FIG. 1A)
5) Measure carpet cleaning solution such as Powr-Flite’s
Kold-Powr® per manufacturers recommended ratio
into the clean water tank and fill with hot water from a
very clean bucket. DO NOT use the waste tank to fill
the solution tank as debris could damage the pump or
block the jet. WARNING: DO NOT exceed 150° (65°
C)
6) Replace recovery (dirty water) tank above solution
tank. (FIG. 1A) Add defoamer solution per
manufacturer’s instructions as needed. 2 oz.
Powr-Flite Powr-Defoamer
®
7) Replace the transparent cover. Pull back handle to
lock cover into place. (FIG. 1A) Treat heavily soiled
areas by using traffic lane cleaner such as Powr-Flite’s
Fast Lane®.
PRE-OPERATION INSTRUCTIONS
OPERATION OF SELF-CONTAINED CARPET CLEANER
NNOOTTEE:: (color fastness) Before using carpet cleaning
chemicals, test on an inconspicuous part of the carpet for color
fastness. Place the solution on a small piece of clean white
material or tissue, then rub the carpet vigorously. Excessive
amounts of dye showing on the material would indicate that the
1) Plug main power cable (FIG. 1A) into outlet. WARNING: This machine must be properly grounded.
See grounding instructions.
2) Press the master switch to the on position. Then press the vacuum switch on and the accessory/brush switch to the
right. (FIG 1C)
3) Press and hold the solution switch (FIG 1C) to apply the cleaning solution. Pull the machine backwards at the same
time to clean the carpet. Stop the solution spray about 12” (30cm) before the end so all of the solution is vacuumed
up. Slightly overlap the next cleaning pass to prevent streaking. A two (2) wet pass maximum is recommended to
avoid overwetting and one dry pass without solution spray will aid in drying time. After a few passes, check the
waste tank to see that no foam is present. Add extra defoamer if necessary.
4) Make sure to empty the recovery (top) tank (FIG. 1A) when it is approximately 3/4 full. Do not refill the solution tank
without emptying all the contents of the recovery tank first.
BRUSH HEIGHT
ADJUSTMENT
KNOB - PFX7S & 9S
BRUSH HEIGHT
ADJUSTMENT
KNOB - PFX4S
RECOVERY
(WASTE)
TANK
SOLUTION
(CLEAN WATER)
TANK
CARRYING
HANDLE
TANK COVER
& HANDLE
SOLUTION
SWITCH
CIRCUIT
BREAKER
MASTER
SWITCH
VACUUM
SWITCH
ACCESSORY / BRUSH
SWITCH
MAIN
POWER
CABLE
POWER
CORD
FIG. 1A
PFX7S shown
FIG. 1C
FIG. 1B
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals